Minelab SD 2200D Manuel d'utilisateur télécharger pdf

Finders Super Fix

(A) Attaching Super Fix to your detector

The Super Fix add on housing has been designed to affix onto the RHS of all Minelab P.I. detector

control housings, it is the same height (140mm) and 10mm shorter (110mm) than a SD2000 control

housing and is only 35mm wide.

Super Fix is supplied with two Velcro fastening strips attached to the inner side ready for use. Before

removing the protective layer from the Velcro strips place the Super Fix control model on the RHS of

your Minelab detector to familiarise yourself with the final positioning. You should note that when

attached to a SD 2000, the rear of the Super Fix housing should align with the rear of the detector

control box housing, and the uppermost Velcro strip should position just beneath the bottom of the

riveted armrest bracket. If your detector is a later model SD or GP detector you should align the rear of

the Super Fix to the inside face of the moulded built in rest, you will note that the stereo headphone

sockets have been off set to allow this.

Simply peel away the protective outer layer to expose the self stick surface ready to press onto the

right hand side of your Minelab detector’s control housing when viewed from the rear. Before fixing

first make sure that the side of your control housing is clean of dirt, dust and greasy substances which

may affect proper adhesion.

Your normal four pin battery connector should now be coupled to the socket on Super Fix’s rear panel

and the fly lead with four pin plug attached to the Minelab Control housing making sure that both

connections are firmly tightened.

Instructions for using Super Fix

1. Switch the MASTER POWER switch on Super Fix’s rear face panel to the OFF position

(B) Setting your Minelab detector for Super Fix

SD2000

2. Switch the POWER switch on your Minelab detector to the ON position.

3. Ensure that the M\LAB - S\FIX MODE switch situated on the top of Super Fix’s front face

panel is switched to the M\LAB position.

4. Switch the SPEAKER switch situated at the top of Super Fix’s rear face to the ON position.

5. Now switch the MASTER POWER switch on Super Fix’s rear face panel to the SD2000 Mode.

Super Fix has a built in soft start feature which eliminates the normal loud burst of audio to

headphones and inbuilt speaker, and after initial power up you should now hear an audio output

from the speaker and also from your headphones if they are connected.

6. Set the TONE control on your Minelab detector to between a low position of (nine o’clock) to

a maximum midway position (twelve o’clock) tonal range.

7. Set the THRESHOLD control on your Minelab detector to a midway (twelve o’clock) position.

8. Manually ground balance the detector as usual using the number 1 & 2 ground balance

adjustments.

9. Now go to section (C) Super Fix Settings

SD2100 / SD2100e

10. Switch the POWER switch on your Minelab detector to the ON position.

11. Ensure that the M\LAB - S\FIX MODE switch situated on the top of Super Fix’s front face

panel is switched to the M\LAB position.

12. Switch the SPEAKER switch situated at the top of Super Fix’s rear face to the ON position.

1 2 3 4 5 6 7

Résumé du contenu

Page 1 - Finders Super Fix

Finders Super Fix (A) Attaching Super Fix to your detector The Super Fix add on housing has been designed to affix onto the RHS of all Minelab P.I.

Page 2 - GP Extreme

13. Now switch the MASTER POWER switch on Super Fix’s rear face panel to the SD/GP Mode. Super Fix has a built in soft start feature which eliminates

Page 3

38. Press and then release the TUNE control on the front panel to automatically reduce electrical interference as normal. 39. Should the interferenc

Page 4 - (D) Operating Super Fix

64. Set the BOOST switch on the rear panel to the normal position. 65. Set the TONE control on your Minelab detector to the minimum low position 66. S

Page 5

1. All Minelab SD & GP series detectors are motion detectors which means that no there will be no target response if the searchcoil is held stati

Page 6 - General information:

You are now ready to start detecting:- Briefly switch back to M\LAB Mode and check your ground balance then switch back to S\FIX Mode and start scann

Page 7 - Finders Pty. Ltd

switching the MODE switch from the S/FIX position to the M/LAB position. As regards gold nuggets small targets - from as small as can be detected, a

Plus de documents pour Mesure, test et contrôle Minelab SD 2200D

Voir le document Minelab SD 2200D Manuel d'instructions

Minelab SD 2200D Manuel d'instructions (22 pages)

Commentaires sur ces manuels

Pas de commentaire

Minelab SD 2200D Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Mesure, test et contrôle Minelab SD 2200D. Super Fix Instructions Manuel d'utilisatio

Résumé du contenu

Plus de documents pour Mesure, test et contrôle Minelab SD 2200D

Commentaires sur ces manuels

Produits connexes et manuels pour Mesure, test et contrôle Minelab SD 2200D